Now comes with clear heat shrink over each individual pixel for added durability!!!
These beautiful pixels combine the small size and low profile of the WS2812 chip with supple jumper wires to bring you strands of individually addressable LEDs that are perfect for costumes!
Strands of 25 pixels are offered in two lengths:
6cm jumper length (~ 2 1/2" center to center), total length ~ 5 feet
12cm jumper length (~ 4 7/8" center to center), total length ~ 10feet
Each strand comes plug & play with a male round 4-pin TCL connector at the beginning and female one at the end.
Purchases of multiple strands of 25 will ship in strands of 50, if you would like for your entire order to be sent in strands of 25, just let us know in the note section during check out.
These limited edition pixels are from special runs made to order for our customers' projects. They differ from our standard pixels in at least one and sometimes several features: White only/RGB LEDs, jumper length, jumper color, clear/diffuse pixel head, clear/opaque housing, and waterproof rating. All of the options here are in units of 50 pixels (e.g. strands of 25 will come in pairs).
If you'd like to place an order for a custom run with specs not listed below, just give us a call. Special orders generally require 4 - 6 weeks for delivery.
For the general specs on Total Control Lighting, please see the item Total Control Lighting Pixel Strand of 50, above.
White-only pixels are especially elegant and brilliant for monochrome projects. Normally, a beautiful red, green, and blue LED is soldered to the output of our driver circuit. In this case, we've chosen a beautiful cool white LED and soldered it to the green output of our driver circuit. Power consumption at full brightness is about 1A. If you're ordering 4-pin male or female connectors, we recommend that you specify White in the Notes section -- it'll help you distinguish these strands from our RGB pixels. Available in bullets or squares. Standard distance between pixels: (3" for bullets; 4 1/2" for square base).
Extra-Long Jumper Wire
For projects that require longer distance between the pixels, we have strands of
-50 square-based pixels with 6" (14.25 cm) of wire from center to center (instead of the standard 4 1/3"). The jumper wire is gray.
-50 bullet with roughly a 1ft spacing. With frosted bulb.
-50 bullet with roughly a 1ft spacing. With water clear bulb.
-25 square based pixels with roughly a 1ft spacing. Black wires and black housing with frosted bulb.
Our standard pixels are cast with milky diffusion, allowing for a uniform glow. These special water-clear cast LEDs allow for each individual red, green, and blue LED to shine through, casting a mesmerizing splash of color onto any surface that they're aimed toward. The distance between pixels is the standard 3" from center to center with the lead wire fully extended.
Water-clear pixels are available in bullets, in strands of 50 or 25 (strands of 25 are sold in pairs for a total of 50 pixels).
Fragile pixels have the same spacing as the standard bullet and square-base configurations but without the silicon casing that isolates and protects the chip and with no waterproofing. With minimal electrical isolation/protection, this is the smallest and lightest configuration and is best for costumes and projects that won't see a lot of wear and tear.
The PVC mold that encases the chip on these pixels is opaque white instead of being the standard transparent PVC. They're available in strands of 50 bullets.
These strands of 25 Total Control pixels offer the ultimate in custom
lighting. Each LED is individually addressable to be of any color or
brightness independent of every other LED.
A 4-pin waterproof
connector at each end connects the strand to our Total Control Lighting
controllers, Power-T Connectors, or to another strand of pixels
25-pixel strands can be powered by batteries for
complete portability, by house current with regulated 5vDC, or, if only a single strand, by USB or car cigarette adapter.
Twice as much beauty as the 25-pixel strands of Total Control Lighting!
Each LED is individually addressable to be of any color or brightness independent of every other LED.
A 4-pin waterproof connector at each end of the strand connects it to our Total Control Lighting controllers, Power-T Connectors, or to another strand of pixels end-to-end.
50-pixel strands can be powered by either batteries for
complete portability or by house current with regulated 5vDC.
Pixels come in two standard configurations: square or bullet.
Pixels now come in black pvc with black wires!!!
These power supplies can be used with our Total Control Lighting LED systems which run off DC 5V - 6V. Choose among a DC 5V regulated power adapter (2 Amps), 6V battery cages (4 x D, or 4 x AA), or a USB adapter (for up to 100 pixels).
With our Total Control Lighting strands of pixels -- Each option plugs into our Gateway or Elite Controller and our Power-T Connectors with a 2.5mm barrel connection. Our Pro Controller requires the House Current option. Please Note: One power supply and Power-T Connector are needed for every 100 pixels in your project to keep them glowing bright from end to end.
With our 3-Channel LED strips: plug any of the options into the Slim Controller.
Create your own Total Control Lighting Super Awesome Cube with these laser-cut acrylic cube faces. Each measures 7 1/2" x 7 1/4" and is ingeniously designed to form a cube when snapped together. All faces are identical -- just order four, five, or six to create a free-standing light box.
Each face has 25 laser-cut holes to hold a strand of 25 TCL Bullet or Square pixels. The 1/8" thickness fits perfectly into the détentes of our patented pixel moulds.
Slip some zip-ties (not included) through the laser-cut slots to easily secure the sides of the cube to each other.
Add an extra dimension and achieve a completely different effect with our faceted Keebler Cubes.
With thousands of these faces in stock, the possibilities are nearly infinite.